Baling press PP-135

This model of baler is in demand among enterprises with a small volume of ferrous and non-ferrous scrap metal, it is also suitable for obtaining a license for collecting non-ferrous metal. The PP-135 baler is designed for fast and high-quality pressing of metal production wastes up to 4 mm thick. The pressing part of the chamber is sheathed with wear-resistant plates, which protect the equipment from deformation.

Price list Request a price
Request a price
Calculations will come to your email within 5 minutes!
We do NOT deal with spam emails.

Technical specifications

ModelPP-135
Force150 tons
Chamber size1300х500х700 mm
Bale size500x250 mm
Baling time80 sec.
For detailed information on technical parameters, please contact the sales department
Baling press PP-135
Особенности

Configurations

Front knife
from 76 500 ₽

Installed on the front side of the bale chamber, it cuts off the protruding parts of the overall scrap.

Increases productivity by 21% due to fewer lid operations.
Automation and remote control
from 865 000 ₽

Eliminates the human factor, namely:

The hydraulic system is protected against pressure drops. The system generates an error and does not allow work until its elimination. Also, the system automatically warns when it is necessary to change the oil and filter;
The operator can control the baler using a radio remote control from the reloading cabin, as well as using a SIEMENS touch monitor on the baler itself. The baler and the reloader are operated by one person, which reduces labor costs;
Control over the oil temperature (will not allow working if the oil is not heated to the desired temperature);
Balta Press engineers can remotely, being at the plant, read the errors that occur and make changes to the program using a modem installed on the baler. All electrics and baler control unit are made up of SIEMENS components. The baler is equipped with an intelligent system that will not allow breaking the pressing algorithm.
Installation of manipulator
on request

The manipulator-baler kit solves the main obstacle to achieving high baler performance – chamber loading time

With the manual method, this parameter takes 70% of the cycle time, approximately 5-7 minutes. With the manipulator configuration, this parameter is reduced to 30% and increases the productivity of the baler by 2 times! In addition to speed, instead of 3 workers involved in the scrap collection with the baler, only 1 worker is required: the same person is the operator of the baler and the operator of the manipulator.

This is the same as putting a second baler next to it. A baler with this configuration unleashes its full potential and gives its owner a tangible understanding of the benefits and speed of the work, seen with his own eyes.

Increase in productivity by almost 2 times. Instead of 3 workers, only 1 operator is now required
Smooth start
from 46 000 ₽

A system that evenly starts the engine and pumps. Extends the life of the equipment.

Extends the life of the station up to 12 years.
Guiding grooves on the chamber and piston
from 194 000 ₽

Prevent "chewing" of the metal in the bale chamber and skewing of the pressure plate with uneven distribution of scrap in the chamber. Recommended for processing small scrap.

Increase the service life of the bale chamber by 300% in comparison with the usual one.
Kit of spare parts, tools and accessories
from 71 500 ₽

Having the most popular spare parts at hand is a guarantee of uninterrupted collection of scrap. Be provided with knives, bushings, cuffs in advance. A serviced baler will last longer, which means it will bring income longer. All components are easy to install and do not require any special skills. Our support units will advise you on how to service the baler or provide service work themselves.

Full set of consumable materials for 3 years of work
Cooling system
from 92 000 ₽

Additionally cools the hydraulic oil in the hydraulic system. Recommended for areas with hot climates.

Increases the service life of lip seals and prevents them from deformation and leakage due to overheated oil.
Hopper for loading metal
from 200 000 ₽

The hopper will enable the operator and the worker not to stop the metal loading operations during the baler cycle. This speeds up and allows them to use the baler more efficiently than without a hopper.

This solution is recommended for enterprises with small-sized scrap, where no cropping with a lid is required. The hopper is operated by an additional lever/button by the operator. The hopper can withstand falling metal loads.

It increases productivity and makes it possible to load scrap during the cycle

See also